I bought a (very) used arc welder from a friend a couple of years ago, and it has been very useful. Started to play up a bit today, so decided to check the fuse.
Not good !!!!
Be careful out there
Be careful out there
Julian B
W Sussex, UK
| '62 Early Series I SWB | '72 Series II LWB |
| '56 Citroën Traction Avant |
W Sussex, UK
| '62 Early Series I SWB | '72 Series II LWB |
| '56 Citroën Traction Avant |
Re: Be careful out there
Wow! That really is a bit of a bodge job! Normally it's a few strands of multicore wire wrapped round the old fuse body - nothing as thick as a bolt!
Good job the earth is still connected....
John
Good job the earth is still connected....
John
Haflinger 703AP LWB 1973 - (Once owned by Lady Sutherland & Sons.) Now called "Lurch" !
Have you hit the "DONATE" button at the bottom of the page after reading this post? Many thanks if you have!!
Have you hit the "DONATE" button at the bottom of the page after reading this post? Many thanks if you have!!
Re: Be careful out there
That's the 3000 Amp super fuse!
- AustHaflinger
- Posts: 2472
- Joined: Sun Jan 06, 2013 1:27 am
- Location: Canberra Australia
Re: Be careful out there
At least it wont blow
Haflinger 700AP (73)
Range Rover Sport TDV6 (07)
Landrover FC 101 (77)
Landrover Series 1 SWB Station Wagon (57)
Landrover Series 1 SWB (57)
Jaguar E-type Roadster V12 (71)
Jaguar XJ12C (76)
Range Rover Sport TDV6 (07)
Landrover FC 101 (77)
Landrover Series 1 SWB Station Wagon (57)
Landrover Series 1 SWB (57)
Jaguar E-type Roadster V12 (71)
Jaguar XJ12C (76)
Re: Be careful out there
I found that the standard 13 Amp fuse was insufficient for my spot welder so the solution was: -
and
Now have 30 amp supply from unused cooker circuit from main house consumer unit into a garage RCB box, with 32 and 16 Amp sockets in the garage.
Hope to be welding the platform together during the next few months, just need to get the rest of the frame blasted and primed before welding the new panels and stiffeners to it.
and
Now have 30 amp supply from unused cooker circuit from main house consumer unit into a garage RCB box, with 32 and 16 Amp sockets in the garage.
Hope to be welding the platform together during the next few months, just need to get the rest of the frame blasted and primed before welding the new panels and stiffeners to it.
Best Regards
Stuart
Northampton
Stuart
Northampton
Re: Be careful out there
Looks good. Are you doing the blasting or did you "farm" that part out? Does your spot welder have long arms so you can do the spot welding in the middle of the platform?
We need photo of the kit being used as well - not just before and after!
John
We need photo of the kit being used as well - not just before and after!
John
Haflinger 703AP LWB 1973 - (Once owned by Lady Sutherland & Sons.) Now called "Lurch" !
Have you hit the "DONATE" button at the bottom of the page after reading this post? Many thanks if you have!!
Have you hit the "DONATE" button at the bottom of the page after reading this post? Many thanks if you have!!
Re: Be careful out there
Spot welder is the Clarke CSW13T which has the timer unit and does 2+2. the longest arms I have are 42 cm, and I have a one sided spot-welder attachment for the arc welder for the bits I can't reach. I have to try this out and then decide whether drilled hole and Mig is better - anyone got any experience of this?.
I'm looking at doing the blasting at home with a blast pot, got 13.5 CFM compressor and also n 8.5 as well so would get sufficient flow. Problem will be setting up a booth, may use the easi-up and tarpaulins. Undecided at present.
I'll post as I go along.
I'm looking at doing the blasting at home with a blast pot, got 13.5 CFM compressor and also n 8.5 as well so would get sufficient flow. Problem will be setting up a booth, may use the easi-up and tarpaulins. Undecided at present.
I'll post as I go along.
Best Regards
Stuart
Northampton
Stuart
Northampton
Re: Be careful out there
G,,day . i presume you realise you can run both compressors together .
just connect outlets into a three way then the blaster .
kerry
just connect outlets into a three way then the blaster .
kerry
ex Tasmanian Haflinger agent .
1984 G Wagen 300GD auto
1984 G Wagen 300GD auto